Skip to content
Mivare Mivare Biznes Moje Mivare
Problemy / Błędy wykonawcze

Wrong selection materials — practical guidance and quality checks

"Bad material selection" requires determining the cause before selecting a fix. The visible symptom itself does not tell you which layer or stage has failed. The card shows symptoms, possible causes, first actions, how to fix it and when professional assessment is needed.

Ask Mivi
In brief "Bad material selection" requires determining the cause before selecting a fix. The visible symptom itself does not tell you which layer or stage has failed. The most important thing is to stop the cause, document the condition and control the result before covering or collecting.
Repair cost 6/10

The higher the score, the less costly this problem usually is to repair.

Diagnosis importance 8/10

The higher the score, the more important correct diagnosis is before choosing a repair.

Ease of repair 6/10

The higher the score, the easier it usually is to plan and carry out an effective repair.

In brief

"Bad material selection" requires determining the cause before selecting a fix. The visible symptom itself does not tell you which layer or stage has failed.

First determine the cause and extent, then choose the repair technology. A good fix can't just hide the symptom.

What does this problem mean

The "Bad selection of materials" problem must be considered as a result of the action of the substrate, materials, conditions and workmanship. The visible defect may occur in a layer deeper than the symptom site.

Symptoms and warning signs

  • the defect appears in several places or layers
  • the next step cannot be performed without compensating for the error
  • the effect deviates from the agreed standard or product documentation

Common causes

Several causes are most often considered at the same time:

  • omitted stage of preparation or control
  • wrong order, rush or work beyond technical conditions
  • inappropriate materials, tools or lack of responsibility for reception

How to assess the scale of the problem

The assessment should answer three questions: whether the problem is active, how deep it goes, and what will happen after the next layer is applied.

  • compare the condition with the scope, design and instructions of the system
  • determine which layers are defective and what has already been covered
  • separate the technical defect from the aesthetic difference and tolerances agreed before work

What to do right away

The first actions are to limit the damage and maintain the possibility of diagnosis:

  • stop covering the defective area
  • take photos, measurements and describe the place
  • determine the person responsible and the deadline for the decision fix

How to find the actual cause

  1. Record the symptom, location, date and conditions of occurrence.
  2. Inspect adjacent features and layers that may be the source.
  3. Perform measurements or testing in a non-destructive manner.
  4. Only after diagnosis should plan an outcropping or disassembly.
  5. Compare the result with the system documentation and scope of work.

How to fix

Remediation depends on the actual cause, but usually includes:

  1. remove the cause at the earliest faulty stage
  2. agree on patch technology and re-commissioning criteria
  3. perform the patch before continuing dependent work

What to avoid

  • oral arrangements without writing down
  • masking the defect with another layer
  • reception only from a distance or in unfavorable lighting

Common errors

  • repairing only the visible surface
  • lack of documentation before dismantling
  • covering the problem with another layer
  • selection of material without checking the substrate and conditions

Urgency, cost and risk of deepening

When to call a professional

Call a professional or independent specialist when one or more of the following signals are present:

  • the defect involves construction, installation, waterproofing or safety
  • the parties disagree on the cause and scope
  • the correction requires the demolition of several layers or an assessment independent

Inspection after repair

The repair can be considered closed only after inspection under normal conditions of use:

  • re-acceptance protocol and closure of each point
  • compliance of the patch with the technology and further work
  • no transfer of the defect to adjacent points surfaces

Frequently asked questions

Does "Bad material selection" mean a serious fault?

"Bad material selection" requires determining the cause before selecting a fix. The visible symptom itself does not tell you which layer or stage has failed.

How to find the cause of the "Bad material selection" problem?

Document the symptom, check adjacent features, take basic measurements, and only then plan for an outcrop. Do not assume that the source is directly under the visible defect.

Can "Bad Material Selection" be repaired by yourself?

A localized and stable defect can sometimes be corrected on your own after identifying the cause. Entrust installations, construction, tightness, extensive moisture and large disassemblies to a specialist.

What happens if I postpone the repair "Bad material selection"?

The rating depends on the scope, substrate condition and risk for subsequent layers.